how to move plumbing lines for a washing machine

Friday, August 12, 2022 Edit

Attach the drain hose to the drain hole beside the water inlet valve by bending it into a u-shape. Drape the drain hose over the side of the utility sink and clamp it firmly in place.

Operation Laundry Room Relocating The Washer And Dryer Reality Daydream

From the trap the waste pipe must run through your outside wall to a hopper head or gully or directly into a soil stack.

. You need to move both the vent line and drain line over separately as vents must be connected within 5 or 6 depending on 1 14 or 1 12 line respectively of the trap. Follow edited Aug 19 2013 at 1353. This ones going to be connected to the vent pipe.

The vent must be within 60 inches of the P-trap for a 2-inch drain. Washing machines typically require a 2-inch drain line with a vent. Screw the machines supply lines to the valves and tighten with pliers.

The washing machine usually includes this. Set the pipe two inches from the adjacent wall and about 36 inches from the ground. Stub the pipe out about 2 inches from the wall and 36 to 42 inches above the floor.

The last thing youd want is to trip on your washers swinging cable during the moving process. The drain piping starts with a standpipe a vertical pipe that connects to a P-trap at the bottom and is open at the top to receive the washing machines drain hose. This Old House plumbing and heating expert Richard Trethewey re-plumbs a washing machine.

Relocating your washing machine gets trickier when plumbing costs are involved. There should also be an outlet from a two-inch sanitary tee thatll face upward. The air gap at the top of the standpipe will stop any dirty water siphoning back into the machine.

Glue on an ABS P-trap. Unplug the washer then use an adjustable wrench to unscrew the existing water supply hoses placing the ends into a bucket to drain any water remaining in the lines. Attach an ABS pipe measuring two inches long to the wall where the washing machine will be installed.

Glue a 10-inch length of. Set the washing machine in place and level it. The main ventilating system should be connected to the drain hole.

Then bend the hose into a U-shape and hook it up to the drain hole. Your washing machine cut-off valve will likely cost around 10 to 30 for each line. Generally the greater the distance the higher the cost.

Its not the distance from the house that matters its the distance from the supplies. Do the same for the cold water hoses. Building a Drain Line for the Washer.

Similarly you will need to remove the drain line and place it into the bucket to empty any remaining water. Turn it on a full cycle. If your walls are not finished the studs are exposed or if you are able to run pipes through walls you can install a washing.

Next get your helper or helpers to carefully lift your machine onto a dolly. If you are using a water softener you will need to add a small amount of distilled water to your water supply. Secure the washer to the dolly with ropes.

Ad Read Reviews from Real Customers Compare Ratings and Connect With Local Plumbers. Keep the machine upright as you wheel it through and out of the house. One option is to hook the hose into the top of an open standpipe with a P-trap at its base.

Once you are satisfied that the water supply and drain lines are empty. The cost will be determined by the cost of getting both the power cold water feed and waste to the new position. Itll certainly be more than 50 though.

Follow these steps to learn the proper way to move a washing machine. 128k 76 76. Twist on the connector from the hot water faucet to the hot water outlet on the back of the machine.

Plumbing dryer drain washing-machine. And one major plumbing cost to relocate your washer and dryer is building a drain line. Secure the power cord to the back of your appliance use a bit of packing tape to make sure it stays in place.

Depending on how close it is to the existing plumbing. Once this is done you have finished plumbing the water supply. After youve connected the hoses to the water supply faucets or shut off valves you will connect the hoses to the rear of the washing machine.

Fasten the power cord. If your washing machine comes with a filter for your drain hose connect the filter. Hold the blankets in place with a cord or packing tape.

See below for a shopping list and toolsSUBSCRIBE to This Old Hou. Let it fill with water and drain to ensure proper function.

Moving Washer And Dryer Laundry Plumbing Layout Laundry Room Diy Laundry Room Layouts Plumbing Layout